How To Use
Charging
- Remove your E-SKN PRO charger from the box and connect it to your device through the side charging portal. Insert the USB connector into your chosen power source. The charger can be connected to both USB wall plug adapters (not Included) or directly into USB charging slots. The LED light ring will flash Red and then produce two White LED lights to indicate charging has begun. Your E-SKN PRO light ring will turn Green when your device is fully charged.
(To ensure battery care and longevity, charge fully once a week and remove immediately from charger once full charge is reached. DO NOT leave the device unattended while charging. DO NOT place charger though charging port while device is wet)
Power On/Off and Mode Settings
- To turn on your E-SKN PRO Device press and hold the Power/Mode button for 3 Seconds. Your LED light ring will light up Blue and go straight into Export Mode when the device powers on.
- To cycle through modes, single-click the Power/Mode button, stopping when the chosen mode is identified. (Modes are identified by LED light ring colour)
- To turn off your E-SKN PRO Device, press the Power/Mode button for 3 Seconds. Your LED light ring will display no light when the device powers off.
- The E-SKN PRO will automatically turn itself off after 4 Minutes of inactivity.
Intensity Selection (+/-)
(Each mode (excluding Photo Therapy Mode ) has 4 intensity settings - Low / Medium / High / Full Strength - These settings affect the intensity of light therapy / Sonic cleaning power / Thermal heating strength / EMS micro-current)
We Recommend starting out on the low setting and increasing the intensity settings week by week.
- Once the desired mode has been selected you can increase and decrease intensity using the + and - buttons on the device. To select the low intensity setting press the (-) button until only two lights are visible within the light ring. Then press the (+) button once to increase the intensity to medium, showing four lights within the light ring. Press the (+) button once more to increase the intensity to high, showing six lights within the light ring. Finally press the + button once again to select the full strength setting. This will display eight lights / fully illuminated light ring.
Export Mode
Blue Light Therapy - EMS Micro Current - Thermal Heating - Anti-Acne and Oil Balancing - 4 Minute Treatment
- Before turning on your E-SKN PRO attach a pre-prepared cleansing pad or makeup wipe to the device using the magnetic Halo.
- Turn on the device and select the Blue Export Mode and preferred intensity setting.
- The moisture in the pre-attached wipe or pad will activate the ION Sensor bar and the vibrating, EMS Microcurrent technology. When this begins place the device onto the skin. The thermal heating will become apparent as you glide the PRO across your face and neck. (If pulsating stops place thumb on ION Sensor bar to activate EMS Micro currents)
- After 3 minutes remove the cleansing pad or wipe and work the device over the face in long, sweeping motions, focusing on problem areas of acne and oil such as the T-Zone and Cheeks.
- After the four-minute treatment time is up the PRO will automatically turn off.
PRO TIP: For an intense Anti-Acne, Spot fighting boost, restart the device after completing the above treatment and select the Blue Import Mode again. Continue to glide the device over troublesome outbreak areas for a full four-min.
Cleansing Mode
Green Light Therapy - Sonic Vibrations - Smooths and Brightens skin - 4 Minute Treatment
- Before turning on your device, wet your face with warm water then add your preferred facial cleanser to the center of the silicone brush.
- Turn on the device and select the Green Cleansing Mode and preferred intensity setting.
- In circular motions use the vibrating silicone bristles to work the cleanser into your face, ensuring to reach all areas of the face and neck to hygienically remove makeup, dirt, and oil from the skin.
- After 3 minutes rinse the device under running water to remove excess product then turn the device around and apply the rotating green light to the face until the end of the four-minute treatment.
- After the treatment time is up the PRO will automatically turn off.
Import Mode
Red Light Therapy - EMS Micro Current - Thermal Heating - Reduces Fine Lines and Wrinkles - Aids Collagen Production - 4 Minute Treatment
- Before turning on your device, apply your preferred face mask.
- Turn on the device and select the Red Import Mode and preferred intensity setting.
- Place your thumb onto the ION Sensor bar, then place the device on top of your face mask. The EMS Microcurrent technology will begin to pulsate and the thermal heating will become apparent as you glide the PRO across the mask. (If the moisture of the mask doesn't activate the pulsation, keep your thumb on the ION Sensor bar to activate EMS Micro currents)
- After 3 minutes remove the face mask and place the device directly onto the skin. Work the excess serum into the face with the device, concentrating the red light therapy on areas of the face where you are concerned about fine lines and wrinkles until the end of the four minute treatment.
- After the treatment time is up the PRO will automatically turn off.
PRO TIP: For an intense anti-wrinkle and collagen boost, restart the device after completing the above treatment and select the Red Import Mode again. Continue to work the excess serum into the skin for another full four minute treatment. This Intense boost will increase the anti-aging features of the E-SKN PRO
Photo Therapy Mode
Purple Light Therapy - Thermal Heating - Eliminate Toxins - Promote cell rejuvenation - 4 Minute Treatment
- Before turning on your device, evenly apply your preferred hydrating lotion or moisturizer, but do not fully rub in.
- Turn on device and select the Purple Photo therapy Mode and preferred intensity setting.
- Place the device against the skin and use the heat therapy to work in the remaining lotion or moisturizer with long, upward sweeping motions.
- Ensure to cover all areas of the face and neck to promote cell rejuvenation and to increase the amount of toxins removed from the skin during the four minute treatment.
- After the treatment time is up the PRO will automatically turn off.
Your Skin Care Routine Is Now Complete!
Device Cleaning
- After each use, apply a mild soap to the silicone side of your device. Work the soap through the bristles with your thumbs or fingers, ensuring to remove any remaining product.
- Flip the device over and using your thumbs and fingers gently remove any remaining product from the metal alloy head and light ring with the soap.
- Rinse off the soap by holding your E-SKN PRO under a running tap. For best results, hold at a 45 degree angle to ensure the water rinses away any left over product.
- When all the soap has washed away, allow your device to air dry in a ventilated space. (To speed up the drying process you can pat the device dry using a lint free cloth or towel )
DO NOT WASH YOUR DEVICE IN A DISHWASHER AND DO NOT SUBMERGE YOUR DEVICE IN WATER TO CLEAN.
E-SKN
E-SKN Gift Cards
